Difference between revisions of "Getting Started with the Terrain Editor"
(→Zones Tab) |
(→Map Window) |
||
| Line 165: | Line 165: | ||
|-valign="top" | |-valign="top" | ||
| width="270" | [[Image:Temap.jpg|Map Window]] | | width="270" | [[Image:Temap.jpg|Map Window]] | ||
| − | | width="100%" | | + | | width="100%" | This window is a quick navigation aid while editing a terrain. It contains the same clipboard map that will be seen in the game itself. It can be resized by dragging the corners of the window for better viewing. |
| + | |||
| + | To zoom in and out on the map use the mouse wheel. | ||
| + | |||
| + | Right clicking on the window brings up an option list that contains the following: | ||
| + | |||
| + | * Show Circles - Shows the radar circles around the towns and fields on the map. | ||
| + | * Show Field Numbers - Shows a graphical representation of the field and it's number on the map. Similar to the clipboard map in the game. | ||
| + | * Show Entry Points - Shows all vehicle and boat entry points on the map. | ||
| + | * Show Zone Lines - Shows a connecting line between the Zone Masters and their related bases. | ||
| + | * Show Field Links - Shows the assigned capture (or uncapturable) order of bases. | ||
| + | * Setup Circles - Allows you to change the radius of the circles shown on the map. | ||
|- | |- | ||
|} | |} | ||
Revision as of 10:31, 17 April 2008
This area is intended to familiarize you with all of the editing controls and their locations in the Terrain Editor for Aces High II. And, it will also show you how to start a new terrain.
Contents
The Terrain Editor Screen
Terrain Tab
The Terrain Tab is used while setting elevations and texture types on a terrain.
|
Set Type: Sets the terrain texture type for the area you are editing in the main window
Refresh Cnts: Refreshes the terrain texture type counts shown in the Terrain Tab Subtype: This only becomes active for river textures and allows you to select the direction a river travels. Randomize: Creates either completely random terrain textures across the whole terrain or randomizes the texture sub-types in a single grid Manual: Manually sets the terrain texture sub-types in a 1 mile grid Save Textures: Exports all of the terrain textures for viewing or editing Auto Type: Allows elevation to be set to Terr Alt when the texture type is selected. Terr Alt: The altitude you want for the point(s) you are editing Set Terr Alt: Sets the altitude of the points you are editing at Terr Alt Inc Alt: Used to raise or lower the terrain in small increments. Raise: Raises the terrain by the value set in Inc Alt Lower: Lowers the terrain by the value set in Inc Alt Setup Filter: Used for creating natural looking hills and valleys over large areas Perform Op: Applies the filters set up in Setup Filter Show Transitions: Water Not 0: Checks for any areas of water that are not at 0 altitude Select: Selects an area to be copied Set Source: Sets the source point to be copied Set Destination: Sets the destination point to be copied Copy: Copies the selected area to the locations set in Set Source & Set Destination Mirror Right: Mirrors the selected area right or up(note: can be modified with Set Source and Set Destination) Flatten Terr: |
Objects Tab
The Objects Tab is used while placing objects such as bases, carrier groups and guns on your terrain.
Task Groups Tab
The Task Groups tab is used to assign initial paths to the Carrier Task Groups in the game.
Roads Tab
The Roads Tab is where you assign routes for supply convoys (roads), trains, and barges that supply bases and strat in the game.
Zones Tab
|
Field List: Lists all fields on the terrain.
Properties: Allows setting a field as a Zone Master Swap Zones: Allows swapping of zones from one area to another by changing zone numbers. |
Map Window
Terrain Window Options
|
Description here |
Position
|
Description here |
Terrain View
|
Description here |
Alt, Options, Time
|
Description here |
Starting a New Terrain
Initial Tutorial










