This area is intended to familiarize you with all of the editing controls and their locations in the Terrain Editor for Aces High II. And, it will also show you how to start a new terrain.
The Terrain Editor Screen
Terrain Tab
The Terrain Tab is used while setting elevations and texture types on a terrain.
|
Set Type: Sets the terrain texture type for the area you are editing in the main window
Refresh Cnts: Refreshes the terrain texture type counts shown in the Terrain Tab
Subtype: This only becomes active for river textures and allows you to select the direction a river travels.
Randomize: Creates either completely random terrain textures across the whole terrain or randomizes the texture sub-types in a single grid
Manual: Manually sets the terrain texture sub-types in a 1 mile grid
Save Textures: Exports all of the terrain textures for viewing or editing
Auto Type: Allows elevation to be set to Terr Alt when the texture type is selected.
Terr Alt: The altitude you want for the point(s) you are editing
Set Terr Alt: Sets the altitude of the points you are editing at Terr Alt
Inc Alt: Used to raise or lower the terrain in small increments.
Raise: Raises the terrain by the value set in Inc Alt
Lower: Lowers the terrain by the value set in Inc Alt
Setup Filter: Used for creating natural looking hills and valleys over large areas
Perform Op: Applies the filters set up in Setup Filter
Show Transitions:
Water Not 0: Checks for any areas of water that are not at 0 altitude
Select: Selects an area to be copied
Set Source: Sets the source point to be copied
Set Destination: Sets the destination point to be copied
Copy: Copies the selected area to the locations set in Set Source & Set Destination
Mirror Right: Mirrors the selected area right or up(note: can be modified with Set Source and Set Destination)
Flatten Terr:
|
Objects Tab
The Objects Tab is used while placing objects such as bases, carrier groups and guns on your terrain.
|
Selec: Selects an object on the terrain
Move: Allows you to move an object selected with Selec
Copy: Copies an object selected with Selec
Rotate: Rotates an object selected with Selec
Group Rotate: Rotates multiple objects selected with Selec the same time
Save Texture: Save the textures for the shape selected in the Available Shapes list.
U, L, R, D: Quick rotate up, left, right and down of an object.
Add Shape/Group: Adds a shape or shape group that is selected in the available shapes list or shape groups list to the terrain.
Delete Group: Deletes an item in the Shape Groups list. USE WITH CAUTION
Selection List: The list of items selected with Selec. Double click on an item to bring up it's property list.
Goto Object: Goes to an object selected in the Selection List
Unselect Object: Removes an object from the Selection List (does not delete object)
Delete: Deletes an object selected in the Selection List
Save Shape Group: Saves items in the Selection List as a Group
Change All: Changes all properties for all items in the Selection List
Select Objects: Select objects by country, field number, shape type or type.
Search for an object by name: Find an object by it's name. ie: f01gms000
Obj Report: Used to check the terrain for errors.
Swap Fields: Swaps field numbers of bases.
Check Entry: Checks vehicle entry points for errors.
|
Task Groups Tab
The Task Groups tab is used to assign initial paths to the Carrier Task Groups in the game.
|
List Window: The list of Carrier Task Groups that are on the terrain.
Add Point: Adds a waypoint for the selected Task Group
Clear Points: Clears all waypoints for the selected Task Group
Looped: Sets the waypoint type to Looped. In other words, the fleet will travel in a continuous loop.
Patrol: Sets the waypoint type to Patrol. In other words, the fleet will travel to the last waypoint, turn around and return following the same path to the first waypoint.
Submit: Finalizes the waypoints for the Task Group.
|
Roads Tab
The Roads Tab is where you assign routes for supply convoys (roads), trains, and barges that supply bases and strat in the game.
|
Set Properties: Changes the road type to road, train or river. Allows changing the road name and type of resources it carries.
Roads Drop Down List: List of roads on the terrain
Add, Delete Road: Manually adds or deletes a road on the terrain
Insert, Add, Delete Point: Insert, Add or Delete a segment to a road on the terrain
Move To: Move focus on a selected road to the First, Next or Last segment of the road.
Show All Roads: Shows all roads on the terrain
Create All: Automatically creates all required roads on the terrain.
Redo Objects: Deletes all trains, barges and convoys and then recreates them at the end of each road.
Road Properties: Shows the length, type and name of a selected road.
|
Zones Tab
|
Field List: Lists all fields on the terrain.
Properties: Allows setting a field as a Zone Master
Swap Zones: Allows swapping of zones from one area to another by changing zone numbers.
|
Map Window
|
This window is a quick navigation aid while editing a terrain. It contains the same clipboard map that will be seen in the game itself. It can be resized by dragging the corners of the window for better viewing.
To zoom in and out on the map use the mouse wheel.
Right clicking on the window brings up an option list that contains the following:
- Show Circles - Shows the radar circles around the towns and fields on the map.
- Show Field Numbers - Shows a graphical representation of the field and it's number on the map. Similar to the clipboard map in the game.
- Show Entry Points - Shows all vehicle and boat entry points on the map.
- Show Zone Lines - Shows a connecting line between the Zone Masters and their related bases.
- Show Field Links - Shows the assigned capture (or uncapturable) order of bases.
- Setup Circles - Allows you to change the radius of the circles shown on the map.
|
Terrain Window Options
|
Grid: Turns on a 1 mile grid in the main editing window.
Cell Overlay On: Shows terrain clutter in the main editing window.
Snap: Allows precise movement of the cursor in the main editing window.
Snap Spacing: Adjusts the distance the cursor moves when snap is active. It is usually best to leave this at the default value.
|
Position
|
Shows the current position of the cursor in the main editing window.
Position X-0,Z-0 is the center of the map.
As you move South of center, Z becomes a negative number.
As you move North of center, Z becomes a positive number.
As you move East of center, X becomes a positive number.
As you move West of center, X becomes a negative number.
Y is the altitude of the point on the terrain the cursor is set on.
|
Terrain View
|
Heading: Changes your direction of view in the editing window
Pitch: Changes your angle of view in the editing window
Top View: Returns to the default overhead view
|
Alt, Options, Time
|
Alt: Changes the amount of visible terrain in the main editing window.
Animation: Shows movement of convoys, trains and barges.
Time: Changes the time of day in the main editing window.
|
Starting a New Terrain
Initial Tutorial